In quadrantal bearing system, bearing of a line varies from

During a CBR test, the load sustained by a remolded soil specimen at 5.0 mm penetration is 50 kg. The CBR value of the soil will be

The value of lateral friction or side friction used in the design of horizontal curve as per India Roads Congress guidelines is

A square matrix B is skew symmetric if

For a scalar function f(x, y, z) = x² + 3y² + 2z², the gradient at the point P (1, 2, - 1) is

For limit state of collapse, the partial safety factors recommended by IS 456 : 2000 for estimating the design strength of concrete and reinforcing steel are respectively

A thin-walled cylindrical pressure vessel having a radius of 0.5 m and wall thickness of 25 mm is subjected to an internal pressure of 700 kPa. The hoop stress developed is

The point within the cross-sectional plane of a beam through which the resultant of the external loading on the beam has to pass through to ensure pure bending without twisting of the cross-section of the beam is called

The analytic function f(z) = ^{$\frac{z - 1}{z^2 + 1}$} has singularities at

The modulus of rupture of concrete in terms of its characteristic cube compressive strength (f_ck) in MPa according to IS 456 : 2000 is

Deposit with flocculated structure is formed when

A precast concrete pile is driven with a 50 kN hammer falling through a height of 1.0 m with an efficiency of 0.6. The set value observed is 4 mm per blow and the combined temporary compression of the pile, cushion and the ground is 6 mm. As per Modified Hiley Formula, the ultimate resistance of the pile is

The square root of the ratio of moment of inertia of the cross-section to its cross-sectional area is called

Dilatancy correction is required when a strata is

Direct step method of computation for gradually varied flow is

The depth of flow in an alluvial channel is 1.5 m. If critical velocity ratio is 1.1 and Manning’s n is 0.018, the critical velocity of the channel as per Kennedy’s method is

The reference pressure used in the determination of sound pressure level is

Particulate matter (fly ash) carried in effluent gases from the furnaces burning fossil fuels are better removed by

Solution of the differential equation ^{$3y \frac{dy}{dx} + 2x$}= 0 represents a family of

The value of the integral ^{$\int\limits_c \frac{cos (2 \pi z)}{(2z - 1)(z - 3)}dz$}(where C is a closed curve given by |z| = 1) is

The relationship among specific yield (S_y), specific retention (S_r) and porosity ($\eta$) of an aquifer is

In the solution of the following set of linear equations by Gauss elimination using partial pivoting 5x + y + 2z = 34; 4y − 3z = 12 and 10x − 2y + z = −4 The pivots for elimination of x and y are

Laplace transform for the function f(x) = cosh(ax) is

For a scalar function f(x, y, z) = x² + 3y² + 2z², the directional derivative at the point p(1, 2, – 1) in the direction of a vector ^$\acute{i}$– ^$\acute{j}$+^{$2 \bar{k}$} is

The degree of static indeterminacy of a rigidly jointed frame in a horizontal plane and subjected to vertical loads only, as shown in figure below is

The standard normal probability function can be approximated as $F(X_N) = \frac{1}{1+ exp(-1.7255X_N | X_n|^{0.12})}$ Where x_N = standard normal deviate. If mean and standard deviation of annual precipitation are 102 cm and 27 cm respectively, the probability that the annual precipitation will be between 90 cm and 102 cm is

Consider the following statements. I. On a principal plane, only normal stress acts. II. On a principal plane, both normal and shear stresses act. III. On a principal plane, only shear stress acts. IV. Isotropic state of stress is independent of frame of reference. The TRUE statement(s) is/are

A hollow circular shaft has an outer diameter of 100 mm and a wall thickness of 25 mm. The allowable shear stress in the shaft is 125 MPa. The maximum torque the shaft can transmit is

A 12 mm thick plate is connected to two 8 mm plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 90 MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is

Consider the following statements for a compression member. I. The elastic critical stress in compression increases with decrease in slenderness ratio. II. The effective length depends on the boundary conditions at its ends. III. The elastic critical stress in compression is independent of the slenderness ratio. IV. The ratio of the effective length to its radius of gyration is called as slenderness ratio. The TRUE statements are

The laboratory test results of a soil sample are given below: Percentage finer than 4.75 mm = 60 Percentage finer than 0.075 mm = 30 Liquid Limit = 35% Plastic Limit = 27% The soil classification is

Water flows through a 100 mm diameter pipe with a velocity of 0.015 m/sec. If the kinematic viscosity of water is 1.13 ^_x 10^–6 m²/sec, the friction factor of the pipe material is

A rectangular open channel of width 4.5 m is carrying a discharge of 100 m³/sec. The critical depth of the channel is

Group I gives the shear force diagrams and Group II gives the diagrams of beams with supports and loading. Match the Group I with Group II. Group I

Group II

A plate load test is carried out on a 300 mm ^_x 300 mm plate placed at 2 m below the ground level to determine the bearing capacity of a 2 m ^_x 2 m footing placed at same depth of 2 m on a homogeneous sand deposit extending 10 m below ground. The ground water table is 3 m below the ground level. Which of the following factors does not require a correction to the bearing capacity determined based on the load test?

The heats of combustion of C₂H₆, C₂H₄ and H₂ are - 1558.3 kJ, - 1409 kJ and - 285.6 kJ respectively. The heat of hydrogenation of ethene is:

Water ($y_\omega$= 9.879 kN /m³) flows with a flow rate of 0.3 m³/sec through a pipe AB of 10 m length and of uniform cross-section. The end ‘B’ is above end ‘A’ and the pipe makes an angle of 30º to the horizontal. For a pressure of 12 kN/m² at the end ‘B’, the corresponding pressure at the end ‘A’ is

Column I gives a list of test methods for evaluating properties of concrete and Column II gives the list of properties.

The correct match of the test with the property is

An agricultural land of 437 ha is to be irrigated for a particular crop. The base period of the crop is 90 days and the total depth of water required by the crop is 105 cm. If a rainfall of 15 cm occurs during the base period, the duty of irrigation water is

A horizontal flow primary clarifier treats waste water in which 10%, 60% and 30% of particles have settling velocities of 0.1 mm/s, 0.2 mm/s, 0.2 mm/s, and 1.0 mm/s respectively. What would be the total percentage of particles removed if clarifier operates at a Surface Overflow Rate (SOR) of 43.2 m³/m².d?

Direction: Examine the test arrangement and the soil properties given below.

The maximum resistance offered by the soil through skin friction while pulling out the pile from the ground is

Which of the following stress combinations are appropriate in identifying the critical condition for the design of concrete pavements?

The correct match of Column I with Column II is

Direction: Examine the test arrangement and the soil properties given below.

The maximum pressure that can be applied with a factor of safety of 3 through the concrete block, ensuring no bearing capacity failure in soil using Terzaghi’s bearing capacity equation without considering the shape factor, depth factor and inclination factor is

The magnetic bearing of a line AB was N 59º 30’ W in the year 1967, when the declination was 4º 10’ E. If the present declination is 3ºW, the whole circle bearing of the line is

On a specific highway, the speed-density relationship follows the Greenberg’s model [v = v_f In (k_j/k)], where v and k_j are the free flow speed and jam density respectively. When the highway is operating at capacity, the density obtained as per this model is

The correct match of Column I with Column II is

Determine the correctness or otherwise of the following Assertion [a] and the Reason [r]. Assertion [a]: Curvature correction must be applied when the sights are long. Reason [r]: Line of collimation is not a level line but is tangential to the level line.

A three-phase traffic signal at an intersection is designed for flows shown in the figure below. There are six groups of flows identified by the numbers 1 through 6. Among these 1, 3, 4 and 6 are through flows and 2 and 5 are right turning. Which phasing scheme is not feasible?

A rest vertical curve joins two gradients of +3% and -2% for a design speed of 80 km/h and the corresponding stopping sight distance of 120 m. The height of driver’s eye and the object above the road surface are 1.20 m and 0.15 m respectively. The curve length (which is less than stopping sight distance) to be provided is

Direction: One hour triangular unit hydrograph of a watershed has the peak discharge of 60 m³/sec.cm at 10 hours and time base of 30 hours. The ^$\phi$ index is 0.4 cm per hour and base flow is 15 m³m/sec.

The catchment area of the watershed is

Direction: Following chemical species were reported for water sample from a well:

Total hardness in mg/L as CaCO₃ is

Using the properties of the clay layer derived from the above question, the consolidation settlement of the same clay layer under a square footing (neglecting its self weight) with additional data shown in the figure below (assume the stress distribution as 1H : 2V from the edge of the footing and$y_{\omega}$= 10kN/m³) is

Direction: Following chemical species were reported for water sample from a well:

Alkalinity present in the water in mg/L as CaCO₃ is

Direction: In the cantilever beam PQR shown in the figure below, the segment PQ has flexural rigidity EI and the segment QR has infinite flexural rigidity.

The deflection of the beam at ‘R’ is

A saturated undisturbed sample from a clay strata has moisture content of 22.22% and specific weight of 2.7. Assuming ^$y_\omega$ = 10 kN/m³, the void ratio and the saturated unit weight of the clay, respectively are

Direction: One hour triangular unit hydrograph of a watershed has the peak discharge of 60 m³/sec.cm at 10 hours and time base of 30 hours. The ^$\phi$ index is 0.4 cm per hour and base flow is 15 m³m/sec.

If there is rainfall of 5.4 cm in 1 hour, the ordinate of the flood hydrograph at 15^th hour is

Direction: In the cantilever beam PQR shown in the figure below, the segment PQ has flexural rigidity EI and the segment QR has infinite flexural rigidity.

The deflection and slope of the beam at ‘Q’ are respectively

A rectangular concrete beam of width 120 mm and depth 200 mm is prestressed by pretensioning to a force of 150 kN at an eccentricity of 20 mm. The cross-sectional area of the prestressing steel is 187.5 mm². Take modulus of elasticity of steel and concrete as 2.1 _^x10⁵ MPa and 3.0 _^x10⁴ MPa respectively. The percentage loss of stress in the prestressing steel due to elastic deformation of concrete is

In the theory of plastic bending of beams, the ratio of plastic moment to yield moment is called